Shaft Accessories

set screw for safety collar 1/4"

set screw for safety collar 1/4" set screw 

BRONZE SHAFT LOG 8" X 3-1/2" BASE

Bronze shaft log, 8" x 3-1/2" base, fits 1.62" and 1.75" I.D. hose, 16-degree angle.    Bin Number (ISBN): 81820

5IN. COUPLER SINGLE TAPER 1-1/8IN. BORE

5" Diameter single taper shaft coupling with a 1-1/8" straight bore (keyed). Includes set screws. Fits Velvet Drive 71C reduction gear (Powerslot) or all 72C direct drive   Bin Number (ISBN): 11314

4" SINGLE TAPER COUPLER 1 BORE

For 1" diameter shafts that are only tapered on the prop end. This should be an interference/press fit onto the shaft. This coupler is usually used with a 1:1 ratio transmission.   Bin Number (ISBN): 33005

DRIVE SHAFT COUPLING BOLT SET

3/8-16 x 1-1/4" (Nylock nuts) S30400 stainless, Velvet Drive coupler and PCM 40 series. Not lomg enough for 2013 and newer PCM 80 series transmissions with 1/2" thick flanges.     Bin Number (ISBN): 2232

KEY STRAIGHT BRASS

1/4" SQ x 2" L Prop Key, may have to cut length to fit some newer boats. The chamfered or radius side goes towards the shaft and the straight edged side fits into prop.   Brass Key. D.I.M. has a large selection of nuts, keys, and cotter pins...

COTTER PIN .16 X 1.5, C/O PROP NUT

Common size for prop nut (5/32" X 1" SST)   Cotter Pins. D.I.M. has a large selection of nuts, keys, and cotter pins in both brass and stainless steel   Bin Number (ISBN): 2200

NYLOCK PROP NUT 1-1/4" SHAFT NUTNYBR789

Fits boats with 1-1/4" shaft (Not for 1" or 1-1/8" shaft). Nautique G-boats, some Malibu/Axis. Brass nut with nylon insert 7/8-9.   Nylock Prop Nut 1-1/4" Shaft | NUTNYBR789 | Discount Inboard Marine   Bin Number...

PROP NUT, CC

Fits 1" or 1-1/8" shafts, the castle nut can be replaced with Nylock nut but will cover up the cotter pin hole (no longer need cotter), 3/4-10 thread.   OLD part # NUTSLBR3410   Bin Number (ISBN): 2004210

PROP NUT, NYLOCK, 3/4X10

Brass Nylock Nutn Fits 1" or 1-1/8" shafts, 3/4-10 thread.   D.I.M. has a large selection of nuts, keys, and cotter pins in both brass and stainless steel. We recommend the nylock nut over the castle nut. If you have a Nautique with the castle...

PROP LOCK

"The Defender" is a great theft deterant for boats in public storage. Fit's 1" or 1-1/8" shafts that have the standard 3/4 -10 thread.     Protect your propeller and deter thieves with the Defender anti-theft inboard prop nut from A.R.E. The...

STAINLESS STEEL SAFETY WIRE (SOLD PER FOOT)

STAINLESS STEEL SAFETY WIRE-- THIS PRODUCT IS SOLD PER FOOT.   USED TO SECURE PACKING NUT ON STUFFING BOXES AND DRILLED NUTS ON RUDDERS.

ZINC, RUDDER 3-3/4

A sacrificial magnet to fight electrolysis in salt water and brackish water applications. 3-3/4" O.D. zink with stainless bolt/nut and copper bushing for permanent ground. Bin Number (ISBN): 101812  

ZINC, BARRELL, 1-1/8 SHAFT

Barrel collar for 1-1/8" shaft. Allen screw held in by washer with stainless nut cast in, copper contact for permanent ground.   Bin Number (ISBN): 102012

ZINC, BARRELL, 1 SHAFT

Barrel collar for 1" diveshaft. Allen screw held in by washer with stainless nut cast in, copper contact for permanent ground.   Bin Number (ISBN): 101912