Strut Bearings/Bushings

set screw for strut bushing 1/8"

set screw for strut bushing 1/8''

XPC BEARINGS 1-1/8 X 1-1/2

* Fits Mastercraft V-drives or Boats with 1.52:1 ratio transmisions. Fits Nautique V-drives with 1-1/8" shafts, Fits 2007 up Tige Boats with Southeastern Foundries Struts. Also Fits Supra and Moomba V-Drives. * Each bearing is 2" long, sold by...

XPC BEARINGS 1-1/8 X 1-3/8

* Low friction vesconite material  * Each bearing is 2" long, price includes 2.   Vesconite 100 thermoplastic material does not swell or soften, lasts up to 10 times as long as traditional materials. Reduces shaft growl and wear (sold per pair)...

XPC BEARINGS 1 ID X 1-1/2 OD

*Low friction, vesconite material *Each bearing is 2" long, price includes 2.   INBOARD STRUT BEARINGS 1" ID X 1-1/2" OD Vesconite 100 thermoplastic material does not swell or soften, last up to 10 times as long as traditional materials. Reduces...

XPC BEARINGS 1 ID X 1-1/4 OD

* Low friction, vesconite material * Each bearing is 2" long, price includes 2 * Not recommended for Ski Nautiques   LOW FRICTION INBOARD STRUT BEARINGS Note: If set screws exist, snug them up, same as with the brass bushings. Note: These...

STRUT BUSHING 1-1/8 X 1-1/2

* Most MasterCraft's With Powerslot 1.5:1 ratio Trans. Nautique V-drives with 1-1/8" shaft. 2007 up Tige V-drives with SEF (Southeastern Foundries) struts. Fits Supra and Moomba V-drives.  * Sold per pair 2 bearings 2"...

STRUT BUSHINGS 1-1/8" I.D. X 1-3/8" O.D.

Malibu 1993 and up with 1-1/8" shafts, Direct Drive and V-Drive. (sold per pair). Each bearing is 2" long, price includes 2   Bin Number (ISBN): 22613

BUSHINGS 1" I.D. X 1-1/2" O.D.

* Some Late 70's and 80's MasterCraft With 1:1 Velvet Drive Trans (sold per pair). Each bearing is 2" long, price includes 2.   1. Remove drive shaft. 2. May have to loosen some set screws. 3. Drive the old ones out. 4. Drive the new ones in. One in...

BUSHINGS 1" I.D. X 1-3/8" O.D

* Some Malibu, Mastercrafts, Ski Brendella, Ski Centurions prior to 1992 when they went to 1-1/8" shafts (sold per pair). Each bearing is 2" long, price includes 2.   Worn strut bearings increase vibration and cause additional wear to the drive...

BUSHINGS 1" I.D. X 1-1/4" O.D.

* Most Ski Nautiques, Inboard Supra's, Moomba's (not V-Drive).* Formerly one long piece now sold in pairs for better water flow and easier installation (sold per pair). Each bearing is 2" long, price includes 2.   Worn strut bearings increase...

XPC BEARINGS 1-1/4 I.D. X 1-1/2 O.D

Note: These bearings will probably be loose on the shaft until you put them in the strut. An 0.008 to .0010 squeeze takes place when seated in the strut    Bin Number (ISBN): 10821