Shaft & Strut Hardware

COTTER PIN .16 X 1.5, C/O PROP NUT

Common size for prop nut (5/32" X 1" SST)   Cotter Pins. D.I.M. has a large selection of nuts, keys, and cotter pins in both brass and stainless steel   Bin Number (ISBN): 2200

NYLOCK PROP NUT 1-1/4" SHAFT NUTNYBR789

Fits boats with 1-1/4" shaft (Not for 1" or 1-1/8" shaft). Nautique G-boats, some Malibu/Axis. Brass nut with nylon insert 7/8-9.   Nylock Prop Nut 1-1/4" Shaft | NUTNYBR789 | Discount Inboard Marine   Bin Number...

PROP NUT, CC

Fits 1" or 1-1/8" shafts, the castle nut can be replaced with Nylock nut but will cover up the cotter pin hole (no longer need cotter), 3/4-10 thread.   OLD part # NUTSLBR3410   Bin Number (ISBN): 2004210

PROP NUT, NYLOCK, 3/4X10

Brass Nylock Nutn Fits 1" or 1-1/8" shafts, 3/4-10 thread.   D.I.M. has a large selection of nuts, keys, and cotter pins in both brass and stainless steel. We recommend the nylock nut over the castle nut. If you have a Nautique with the castle...

PROP LOCK

"The Defender" is a great theft deterant for boats in public storage. Fit's 1" or 1-1/8" shafts that have the standard 3/4 -10 thread.     Protect your propeller and deter thieves with the Defender anti-theft inboard prop nut from A.R.E. The...

STAINLESS STEEL SAFETY WIRE (SOLD PER FOOT)

STAINLESS STEEL SAFETY WIRE-- THIS PRODUCT IS SOLD PER FOOT.   USED TO SECURE PACKING NUT ON STUFFING BOXES AND DRILLED NUTS ON RUDDERS.

BUSHINGS 1" I.D. X 1-1/4" O.D.

* Most Ski Nautiques, Inboard Supra's, Moomba's (not V-Drive), 1986 up Mastercraft with 1" shaft.* Formerly one long piece now sold in pairs for better water flow and easier installation (sold per pair). * Some Mastercraft 1985 and prior had 1" X 1-3/8"...

BUSHINGS 1" I.D. X 1-3/8" O.D

* Some Malibu, Mastercrafts, Ski Brendella, Ski Centurions prior to 1992 when they went to 1-1/8" shafts (sold per pair). Each bearing is 2" long, price includes 2.   Worn strut bearings increase vibration and cause additional wear to the drive...

BUSHINGS 1" I.D. X 1-1/2" O.D.

* Some Late 70's and 80's MasterCraft With 1:1 Velvet Drive Trans (sold per pair). Each bearing is 2" long, price includes 2.   1. Remove drive shaft. 2. May have to loosen some set screws. 3. Drive the old ones out. 4. Drive the new ones in. One in...

STRUT BUSHING 1-1/8" X 1-3/8"

Most Malibu 1993 Up with 1-1/8" shaft and OEM strut, also most boats with Marine Hardware struts. * Sold per pair 2 bearings 2" long   Worn strut bearings increase vibration and cause additional wear to the drive shaft. Under normal operating...

STRUT BUSHING 1-1/8" X 1-1/2"

* Most MasterCraft's With Powerslot 1.5:1 ratio Trans. Nautique V-drives with 1-1/8" shaft. 2007 up Tige V-drives with SEF (Southeastern Foundries) struts. Fits Supra and Moomba V-drives.  * Sold per pair 2 bearings 2"...

XPC BEARINGS 1 ID X 1-1/2 OD

*Low friction, vesconite material *Each bearing is 2" long, price includes 2.   INBOARD STRUT BEARINGS 1" ID X 1-1/2" OD Vesconite 100 thermoplastic material does not swell or soften, last up to 10 times as long as traditional materials. Reduces...

XPC BEARINGS 1 ID X 1-1/4 OD

* Low friction, vesconite material * Each bearing is 2" long, price includes 2 * These are very sensative to the original bore of the strut and not recommended for Ski Nautiques. Usually they work       fine but if the strut bore is...

ZINC, RUDDER 3-3/4

A sacrificial magnet to fight electrolysis in salt water and brackish water applications. 3-3/4" O.D. zink with stainless bolt/nut and copper bushing for permanent ground. Bin Number (ISBN): 101812  

XPC BEARINGS 1-1/8 X 1-3/8

* Low friction vesconite material  * Each bearing is 2" long, price includes 2.   Vesconite 100 thermoplastic material does not swell or soften, lasts up to 10 times as long as traditional materials. Reduces shaft growl and wear (sold per pair)...