Shaft & Strut Hardware

5" OUTPUT COUPLING BW 71/72C FINE SPLINE

5" OUTPUT COUPLING BW 71/72C FINE SPLINE

STRUT BUSHING 1-1/8 X 1-3/8

  * Sold per pair 2 bearings 2" long   Worn strut bearings increase vibration and cause additional wear to the drive shaft. Under normal operating conditions, strut bearings are replaced every 300 hours, more frequently in silty or sandy...

DRIPLESS WATER COOLING KIT FOR 1-1/4"

Kit includes  3/8 water line, hose clamps, and stainless t-fitting. Used when installing a dripless seal kit requiring cooling water and boat has 1-1/4'' ID water hose. Used on the pressure side of the raw water pump.  

3-1/2" WALTER COUPLER FOR 1-1/8" SHAFT

Shaft Coupling, Walter V-Drive, 1-1/8" single taper bore, not for dual tapered shafts.  Usually only Correct Craft used non tapered shafts on older V-drives.

STRUT 15 DEGREE (SEF 1051L) L=LONG SUNSPORT

Used on some Supras with 454 and 1" shaft. Also used on some direct drive Moombas with 1" shafts (not V-drive). Includes new strut bearings   *Careful, this is a SEF1051L, there is also an SEF1051 (C/O Outback and Boomerang) it's pt #103082 (not on...

STRUT, MALIBU 1997 UP

A few late 1996 models may have this 16 degree strut . The previous version was a 15.45 degree strut. Also fits Axis boats (but will say "Malibu" on the side). Will not fit XTI or FXI models, includes new strut bearings.   Bin Number...

STRUT, MASTERCRAFT 1986 UP 1-1/8 IN

8 Mounting holes 16 degree (Includes brass shelled rubber strut bearings). Fits 1986 up Mastercraft boats with powerslot or V-drive 1-1/8" shafts. Or, all 2003+ splined shaft. This is an aftermarket strut and will not have Mastercraft on the side...

STRUT, MASTERCRAFT 1986 UP 1"

This strut measures 7-3/4" high from mounting base to bottom of the barrel at the prop end. This is an aftermarket strut and will not have Mastercraft on the side. Note: Replacement strut bushing outside diameter will now be 1" X 1-3/8" no longer 1"...

STRUT MOOMBA/SUPRA 1-1/8 BORE 15 DEGREE

Most V-drive Supra and Moomba with 1-1/8" shaft, has SEF1050 (15 degree) stamped into side. Includes new strut bearings.     Superceeds 121306   Bin Number (ISBN): 60813

STRUT SUPRA 14 DEGREE, 1IN. SHAFT

Includes Bushings, Comp, Some Mariah's and older Sunsport's (Should be stamped with a 14).   Includes strut bushings, fits Supra Comp, some Sunsports and Maria's. Old strut should be marked with a 14 on the side, has a 6-1/2" drop. The distance...

16° STRUT FOR CENTURION BOATS 1998+ WITH 1-1/8" SHAFT

16 degree strut fits Centurion 1998+ boats with a 1-1/8" shaft. 6 hole bolt pattern and includes brass bushings.    

STRUT 15.45 DEGREE (SEF1052)

Fits Direct Drive Outback (not LS) also fits Supra Launch SS Direct drive. LS use strut 103082   Bin Number (ISBN): 22422     *THIS IS A SPECIAL ORDER ITEM

STRUT SUPRA/MOOMBA 15 DEGREE 1'', SEF1051, SHORT

STRUT SUPRA/MOOMBA 15 DEGREE 1'', SEF1051, SHORT Direct Drive REPLACES SKIERS CHOICE #102414 (14.5 DEGREE) STRUT THAT IS NO LONGER AVAILABLE.

XPC BEARINGS 1-1/8 X 1-1/2

* Fits Mastercraft V-drives or Boats with 1.52:1 ratio transmisions. Fits Nautique V-drives with 1-1/8" shafts, Fits 2007 up Tige Boats with Southeastern Foundries Struts. Also Fits Supra and Moomba V-Drives. * Each bearing is 2" long, sold by...

XPC BEARINGS 1-1/8 X 1-3/8

* Low friction vesconite material  * Each bearing is 2" long, price includes 2.   Vesconite 100 thermoplastic material does not swell or soften, lasts up to 10 times as long as traditional materials. Reduces shaft growl and wear (sold per pair)...