ELECTRICAL and TUNE UP

IGNITION SWITCH 4 POSITION/TERMINAL

Polyester housing is rust and corrosion proof. 4 position "Accessory-Off-Run-Start" switch. Four 1/4" blade terminals. Supplied with brass back-up nut and knurled black plastic face nut with rubber cap to seal out splash and spray. Requires 7/8" mounting...

FUEL PRESSURE CUTOFF SWITCH

Carbureted engines with electric fuel pump, can be used to replace 3 wire switches. (For a 3 wire switch, connect the red and orange wires together on one post and the purple wire by itself to the other). Most Indmar will need more clearance use this...

ADAPTER, OIL SENDER (ALL GM)

1/8" NPT female to 1/8" NPT male adapter. Pushes oil sender out about 1/2" for clearance. Bin Number (ISBN): 121012

BUSHING BRASS 1/4" NPT X 1/8" NPT

Bushes the Oil Pressure Sendor on some applications. Others may screw directly into the adaptor.  Bin Number (ISBN): 1245

SENSOR, OIL PRESSURE DIGITAL

2007 PCM 5.7L SN: 480001 up, 6.0L All years and a second one was added to the Intake Manifold in 2011 Pt#R020060.3 wire snap in connector 1/8" NPT. 2012 and up 6.0L and 6.2 LSA use Item #42117. Will NOT fit Indmar engines. Bin Number...

SWITCH WATER TEMP EEMS/GM/EFI/GT40

Fits: 95 & Up GT40, Apex (MPI), 1/2" NPT. 210 Degree (limp Home). #25 in the PCM parts book. Marine Pro Tec Water Temp Switch Bin Number (ISBN): 1238

MODULE DELCO DISTRIBUTOR

MODULE, DELCO DISTRIBUTOR R116014 Electronic Module used with Delco distributors. No spark is a symptom that it needs replaced. Bin Number (ISBN): 62514  

IGNITION MODULE, MALLORY 50/57 SERIES

* Magnetic pick-up replacement module* Not for E-spark distributors (use MAA-6100M) Bin Number (ISBN): 21606  

SWITCH, OIL PRESSURE 6 PSI

Some Indmar thru 2005. Low oil pressure switch for engine alarm (Sierra Brand). 1/8th NPT thread. For a alternative switch used by Pleasurecraft Marine Click Here Bin Number (ISBN): 100615

IGN MODULE TFI GT-40

GT40 MULTI-PORT EFI TFI MODULE   NOTE: replacement unit is only the module - you need to reuse the heat sink from your current one!! The module is attached using 2 5.5MM screws, just unscrew and replace the module from the heat sink. Direct...

SENDER, TRANSMISSION OIL TEMP 88-5178

Transmission temp sender. Used on mostly Mastercraft and Mercruiser, fits Velvet Drive and Hurth transmissions. Goes into top of transmission in a Velvet Drive 71 or 72 C.Also used in some Malibu's for the alarm. Even on some Fords 1990 on up. Bin Number...

MALLORY IGNITION MODULE 6100M

Replacement Ignition Module for Mallory E-spark Distributors, if you are blowing these make sure your using resistance to the coil. Bin Number (ISBN): 52915  

ENGINE ALARM WITH AUDIBLE WARNING

Audible warning system for engine temperature and oil pressure. Keep your engine safe this summer. Works on Ford or GM older applications without alarms, EFI, or Carburated.  Oil pressure switch set a 6psi and temp switch set at 200...

NEUTRAL SAFETY SWITCH

No O-Ring Required. Used up to late 1970's. Old style 1-1/8" size wrench, used up to late 1970's. Bin Number (ISBN): 1246

WATER TEMP SENDING UNIT

PCM 302, GT40 in circulation pump, Some Mercruiser (pt # 806490T), Early LT1 in the T-stat housing then moved to cylinder head around 95 (tapered threads are aprox. 3/4" in diameter). Also used in some PCM GM engines around 2002-05 located in the T-stat...