TRANSMISSIONS

HOSE ASSY, TRANS COOLER RETURN 21.25"

21.25" Length (.406 x 21.25").   Return line for your Borg/Warner Transmission.   Bin Number (ISBN): 1411

H0SE ASSY, TRANS COOLER FEED 13.25"

13.25" Length (.406 x 13.25"). Also used for PCM 40 transmsions to replace the 11" that is NLA.   Feed line for your Borg Warner Transmission!   Bin Number (ISBN): 1410

OIL COOLER 5" BARRELL X 1" OD BARBS

Transmission Oil Cooler 5" BARRELL X 1" OD Barbs R147003 Normally Used On: PCM Ford's With 1:1 Or 1.23:1 Transmissions. 3/8" NPT Fittings (8" tip to tip).   Oil Cooler 5" BARRELL X 1" OD Barbs R147003 here at Discount Inboard Marine. TRANSMISSION...

OIL COOLER 9" BARREL X 1" BARBS

Older PCM Ford's With A 1.52:1 (Powerslot) Transmission. 3/8" NPT Fittings (12" tip to tip)   TRANSMISSION COOLERS The Transmission Cooler is often overlooked when troubleshooting overheating problems. The Cooler should be checked for restriction on...

OIL COOLER 12" BARREL X 1-1/4" BARBS

Cooler used on GM engines with PCM 80 series transmissions, direct drive & v-drive (3/8 NPT fittings).   TRANSMISSION COOLERS The Transmission Cooler is often overlooked when troubleshooting overheating problems. The Cooler should be checked for...

OIL COOLER 5" BARREL X 1-1/4" BARBS

Transmission Oil Cooler 5" Barrel X 1-1/4" OD Barbs R147014: Fits: Indmar Ford/GM, Most PCM GM. 3/8" NPT Fittings (8" tip to tip).  Late 2005 and up Indmar with the o-ring type hydraulic hose fittings will need (2) 50219 adapters...

OIL COOLER 9" BARRELL X 1-1/4" BARBS

Indmar Ford/GM With Powerslot, Also Mercruiser GM . 3/8" NPT Fittings (12" tip to tip).  Late 2005 and up Indmar with o-ring type hydraulic hose fittings need (2) 50219 adapters. Also will not fit later style Mercruiser with a 90 degree...

TRANSMISSION OIL COOLER (DUAL) GM SHAMROCK 12"

12" barrel X 1`-1/4" barbs dual engine oil/trans cooler for use in shamrock boats.   fits: GM, Shamrock    

DAMPER PLATE, PCM 40 SERIES FORD/GM

Use with PCM 40A (1.23:1 ratio) and 40I (1:1 ratio) transmissions. Ford 302 & 351, GM 5.0L, 5.7L and 6.0L engines. The PCM 40 has a 15 spline input shaft. Superceeds PCM Pt. #R140016A.   Bin Number (ISBN): 31011

BOLT, FLYWHEEL DAMPER FORD

 (5/16-18 X 3/4 Sholder Bolt). Six bolts are required. You can re-use the old bolts, fits Ford 351 & 302     **INCLUDES FLATS WASHER AND LOCK WASHER   Bin Number (ISBN): 1520

BOLTS, DAMPER ALL GM

These bolts fit older standard thread flywheels, 3/8-16 X 1". There was a change to a metric thread but we are not sure of the year 2002 up? WILL NOT FIT INDMAR LT1.   Bin Number (ISBN): 1519

DAMPER DRIVE PLATE BW FORD/80 SERIES FORD

Borg Warner Velvet Drive damper plate for 1:1 and 1.52:1 transmissions. Features a 26 spline input shaft. Due to vendor changes, the new replacement dampers may be a different shape than the original.   Nothing Special about the damper...

DAMPER PLATE 8.1L & 6.0L HURTH/ZF

Heavy duty damper plate, 8.1L and 6.0L engines with Hurth/ZF transmissions. Mastercraft Only.   Bin Number (ISBN): 40212

DAMPER PLATE 6.0L, 6.2, 5.3L

Also fits H5 and H6 Direct Injected engines.   Fits PCM 80 series, Hurth and Velvet Drive transmissions with 26 spline input shaft. Will NOT fit older PCM 40 series transmissions, use Item #31011.   Bin Number (ISBN): 41018

DAMPER PLATE, GM 5.7, 5.0L HURTH/ZF

GM Small Block with ZF Hurth Transmissions (Heavy duty). This damper raises the mounting bolts heads about 1/4" and Indmar bellhousings may have to be ground slightly for clearance.Hurth V-drive only, not for ZF45 (HSW 450 D) use Item # 1516.   Bin...