Tools

Star Brite SILICONE SEALANT 2.8oz/ 100ML

Star Brite Brand marine sealant- 2.8oz/100ML bonds to fiberglass plastic, wood, glass, metal and more. For use above and below the water line. 

SYSTEM SOCKET 1.25

1-1/4" Socket With Wrench Flats. Most Mastercraft original equipment driveshaft, with Marine Hardware driveshafts.   The ARE retaining nut socket with wrench flats requires only 1" clearance to fit between the transmission and the coupling...

SYSTEM SOCKET 1.06

1-1/16" Socket with wrench flats. Needed when there is not enough room to get a regular socket/ratchet in between the couplers.* Example Mastercraft's (with ARE shaft) with powerslot transmission and some Supra's with PCM 1.23 transmission...

IMPELLER PULLER, SEA DOG

You will need 5-1/4" clearance in front of the pump and the handle length is 3-1/2" so it needs 1-3/4" clearance from the center of the pump to rotate. Stainless Steel construction, fits 2-1/4" to 2-9/16" impellers.   Bin Number...

ARE SYSTEM SEPARATOR NUT

This nut is included with the ARE drive shaft system. It screws into the drive shaft coupler pressing against the shaft and pops it off. It will only work with the ARE system that has internal threads in the coupler.   Bin Number (ISBN): 11911

DRIVESHAFT PULLER ADAPTER 1-1/4" SHAFT

Enables the A.R.E. shaft removal tool to be used on 1-1/4" shafts, found on Nautique G23 and G25 boats.   Bin Number (ISBN): 83016

STRUT & DRIVE SHAFT BEARING PULLER

The perfect tool for removing your strut, drive shaft bushings. Remove with ease, which means more time on the water and less time dealing with drivetrain issues.   The slide hammer design A.R.E. Shaft/Strut Bearing Puller makes quick work of...

COUPLING WRENCH

This wrench goes in one of the coupling bolt holes and keeps the shaft from turning while loosening the coupling nut.   A.R.E.’s coupling wrench keeps the shaft from turning while removing the retaining nut on double-taper drive shafts. Fits...

PROP WRENCH 1-1/4 X 3/4

Fits "CASTLE NUT" And ARE Puller   3/4" End fits A.R.E. IRONMAN Prop Puller.   Bin Number (ISBN): 81805

OJ PROP HARD CASE W/HARDWARE 15"

Prop Puller, Wrench, Nylock Nut, Cotter Pin, and Prop Key included.   OJ PROP HARD CASE W/HARDWARE 15" Perfect for keeping safe and keeping track of a spare propeller. OJ Prop Carrying case Hardware includes: Puller, wrench,...

ACME PROP PULLER, 1-1/4 C-CLAMP

2014 and up Nautique G-boats. This size is only for the Newer Heavy Ballast V-Drives   2014 and up Nautique G-boats. This size is only for the Newer Heavy Ballast V-Drives. Acme recommends Lucas X-tra heavy duty grease (or similiar) on the puller...

PROP WRENCH A.R.E.

Helps remove NYLOCK NUT and helps tighten the A.R.E. Prop Puller Bolt. TWO WRENCHES IN ONE!   A.R.E.’s chrome-plated prop wrench is laser cut from 1/4" steel and is offset for clearance. 3/4" end fits ARE IRONMAN Puller.   Bin Number...

ACME SOFT CASE PROP SAVER W/C-CLAMP AND TOOLS

A must-have for your boat, this kit comes with everything you need to save a weekend on the water. Replace a damaged prop on the go with this weekend saver prop case from ACME.   Included in the kit: C-Clamp Prop Puller Needle Nose...

OJ PROP KNOCKER

Economical option to the traditional prop puller.Simply screw it on in place of your prop nut and give it a knock with a hammer. It will jolt the prop loose from the shaft. Then, unscrew the knocker and pull off the prop.Fits 1" and 1-1/8" shafts (not...

ACME PROP PULLER, C-CLAMP

Fits 1" and 1-1/8" shafts. Long-lasting durable material     This Acme C Clamp Prop Puller Fits 1" and 1-1/8" shafts. Acme recommends using Lucas X-tra heavy-duty grease (or similar) on the puller threads.   On...